Make a mark where the taper will stop (at the safety pins), then draw a straight line from one mark to the other blending the line into the existing seam at the top. Repeat for both sides of the leg on each leg. Sew along this line using matching thread and a stitch suitable for the fabric of the pants. If the pants have stretch, use a stretch stitch.

Make the line extend from the bottom hem up to about 1 to 2 inches above the knee of the jeans.

A tapered leg has a very clean look and is necessary if you’re going with the no-break look. However, it shouldn’t be tapered to the point where your pants look painted on. My rule of thumb is that the pants still need to feel comfortable.
A tapered leg has a very clean look and is necessary if you’re going with the no-break look. However, it shouldn’t be tapered to the point where your pants look painted on. My rule of thumb is that the pants still need to feel comfortable.
A tapered leg has a very clean look and is necessary if you’re going with the no-break look. However, it shouldn’t be tapered to the point where your pants look painted on. My rule of thumb is that the pants still need to feel comfortable.
Psssh, I should have tapered these bad boys a looooong time ago. Maybe you should too. It’s as simple as turning your pants inside out, pinning each leg evenly, creating the taper you’d like, and sewing (using the pins as your guideline) until the new seam meets back .
To taper pants, you can work from about 3 inches above the knee down to the hem. Determine how much you want to remove from the total hem circumference, and remove an equal amount from the side seams and inseams to make this reduction.
How to Hand-Sew a Padded Jacket Hem | Video

Let Me Show You How to Taper Pants Legs…

Mar 29,  · Tapered pants fit comfortably at the thigh and taper to a narrower ankle (the tapered pants illustrated above also have a high waist and pleats, but it's the leg style only we're looking at here) Skinny pants look best on people with a balanced body vertical body shape, with a bottom that is neither flat nor large and a slim figure, such as a.

Draw a straight line at this mark from the very bottom of the leg to the top of the stitching mark from the existing hem. Make a mark where the taper will stop at the safety pins , then draw a straight line from one mark to the other blending the line into the existing seam at the top. Repeat for both sides of the leg on each leg. Sew along this line using matching thread and a stitch suitable for the fabric of the pants.

If the pants have stretch, use a stretch stitch. If the pants do not stretch, use a regular stitch. Trim the excess fabric away and secure the seam with a zig zag stitch. I used a serger which did all of the finishing work for me! It is very easy to do but if you have questions, leave a comment below! Your email address will not be published.

Notify me of follow-up comments by email. Notify me of new posts by email. Replace the hem using thread that matched the thread from the existing hem. Press the new seam.

Draw a line along the edge of the yardstick to mark this taper,. Measure along the hem from the seams to the lines you drew. Use these measurements to mark the other leg of the pants to match the first leg. Machine sew a seam along the four lines you drew. Turn yoga pants into leggings. Mark the location of your knee on the side seam with a pin. Take off the pants. Draw a line from the knee to the hem on the inseam in the same way. Replace the hems and turn the pants right-side out.

How to Take in Pant Legs.

8 Comments

Tapering the pants should cost no more than $ For your future pant and slack purchases, a good tailor should include this alteration as part of the initial hemming and should ask your preference for the taper the first time you bring them in. If they don’t ask, just let them know that’s what you’d prefer. Step 4: Measure a pair of pants that you like the fit of at the leg opening and mark that on the pair you're tapering. I went with 6 inches for the leg opening. Step 5: Mark where the knee of your pants is. Pivot the edge of the stick until the pants have the taper you desire. Draw a line along the edge of the yardstick to mark this taper, Draw a line from the knee to the hem on the inseam in the same way.